|
|
| |
Connector Type
|
|
|
| |
Your choices are...
|
|
|
| |
BMA / BMMA
|
|
BMA connectors feature a push-on interface and a thread less outer ground connection. They can withstand both radial and axial misalignment. BMMA connectors are miniature BMA connectors.
|
| |
BNC
|
|
Bayonet Neil-Councilman (BNC) connectors were designed for military applications, but are used widely in video and RF applications to 2 GHz. BNC connectors have a slotted outer conductor and a plastic dielectric that causes increasing losses at higher frequencies. BNC connectors are usable above 4 GHz as long as the slots radiate signals; however, these devices may not be mechanically stable to 10 GHz. Both 50 and 75 BNC connectors are available. BNC connectors are also known as bayonet navy connectors or baby Neil connectors.
|
| |
Type C
|
|
Type C connectors are medium-size, weatherproof devices with a two-stud bayonet coupling. They provide constant 50 impedance and may be used with 75 cable below 300 MHz.
|
| |
Centronics Connector
|
|
Centronics connectors are standard parallel interface devices for connecting printers and other peripherals such as portable disc drives, tape backup drives, and CD-ROM players to computers. Centronics connectors, which are also known as blade connectors, are the standard connector for the Hewlett-Packard interface bus (HPIB). They are generally available in 50 and 68 pin varieties.
|
| |
D-Sub
|
|
D-Subminiature (D-sub) connectors have a mating face that is shaped like the letter "D". This shape provides polarization since D-shaped male and female connectors fit together in only one way.
|
| |
DIN Connectors
|
|
DIN connectors are high frequency, multi-pin, electrical connectors that meet standards established by Deutsches Institut für Normung (DIN), a German national organization for standardization. The ends of DIN connectors are round, notched, and protected by a metal skirt to ensure that pins line up correctly. Both male and female DIN connectors are available. Male connectors plug into receptacles, jacks, and outlets and contain three to fourteen pins ranging in size from approximately 5/8” to just under 1” in diameter. Female connectors contain sockets for pins from other devices. The number of pins or sockets in a DIN connector corresponds to the number of wires in the coaxial cable. Often, DIN cables are referred to numerically so that, for example, a four-wire DIN cable is called a “DIN 4”.
|
| |
DVI
|
|
Digital video interface (DVI) connectors are used to transfer digital, audio or video signals.
|
| |
Strip Connectors
|
|
Strip connectors have many contacts. They can have one or more rows (strips) of contacts.
|
| |
SCSI Connectors
|
|
Small computer system interface (SCSI) connectors are used to connect peripherals to computers. These connectors are parallel devices.
|
| |
Type F
|
|
Type F connectors have a screw-type coupling and frequency range up to 1.5 GHz. Applications include CATV, TV, and antennas.
|
| |
IEEE 1394 - 4 Ways
|
|
IEEE 1394 connectors with 4 contacts.
|
| |
IEEE 1394 - 6 Ways
|
|
IEEE 1394 connectors with 6 contacts.
|
| |
FME
|
|
FME connectors are used in mobile antenna applications. With adapters, they can also be used in place of UHF, Mini-UHF, TNC, BNC, and Type N connectors.
|
| |
Type G
|
|
Type G connectors are 75 impedance devices with snap-on coupling. They are well-suited for CATV applications.
|
| |
Box Header
|
|
Header constitutes the base or mounting plate of an electronic package to which chips and leads are attached. A broad category of connector types. Headers are common inside personal computers connecting disk drives, CD drives, and the serial and parallel ports to the motherboard. Box headers have an enclosure around the contacts.
|
| |
Pin Header
|
|
Header constitutes the base or mounting plate of an electronic package to which chips and leads are attached. A broad category of connector types. Headers are common inside personal computers connecting disk drives, CD drives, and the serial and parallel ports to the motherboard. Pin headers do not have an enclosure.
|
| |
MCX
|
|
Miniature coaxial (MCX) connectors provide broadband capability through 6 GHz and are used in applications where weight and physical space are limited. They provide good electrical performance and are used to address the rapid implementation of the U.S. digital cellular PCN infrastructure. MCX connectors are also used in global positioning systems (GPS) and wireless LAN (WLAN) applications.
|
| |
MHV
|
|
MHV connectors are compact, high-voltage devices with 50-ohm impedance and a two-stud bayonet coupling. MHV connectors are similar in size to, but not interchangeable with, BNC connectors.
|
| |
MMCX
|
|
Micro-miniature coaxial (MMCX) connectors are smaller than MCX connectors and feature a more robust interface for greater durability. They are ideal for high volume, wireless SMT or PCMCIA applications in cellular base stations, cellular phones and personal communicators. MMCX connectors are also used in global positioning systems and wireless LAN (WLAN) applications.
|
| |
Type N
|
|
Type N connectors include an integrated gasket to protect against environmental ingress and create an air gap between the center and the outer conductor. They primarily have 50 impedance, but 75 versions for CATV, are available.
|
| |
QMA
|
|
QMA connectors are quick-disconnecting devices that have the same internal construction as SMA connectors.
|
| |
RCA
|
|
RCA connectors are round, press-on connectors commonly used for consumer-grade audio and composite video connections. In most recent home stereo equipment, the jacks are color-coded as follows: red (audio-Right), black or white (audio-Left) and yellow (composite video).
|
| |
RJ-11
|
|
Registered Jack 11 - A four or six wire connector used primarily to connect telephone equipment in the United States.
|
| |
RJ-45
|
|
Registered Jack 45 - An eight-wire connector used to connect computers, printers and other devices into a network.
|
| |
SC
|
|
Subscription channel (SC) connectors are coaxial, medium-size devices with a constant 50 impedance and a frequency range of 0 - 11 GHz. They are larger than BNC connectors, but about the same size as Type N devices.
|
| |
SMA
|
|
Subminiature-A (SMA) connectors are intended for use on semi-rigid cables in components. They directly interface the cable dielectric without air gaps. They are not intended for permanent connections.
|
| |
SMB
|
|
Subminiature-N (SMB) connectors are snap-mount connectors that are available either in 50 or 75 impedances. They are used for frequencies from DC to 4GHz.
|
| |
SMC
|
|
Subminiature C (SMC) connectors are 50 or 75 devices with a frequency range of 7 - 10 GHz. They are smaller than SMA connectors, but can accept flexible cables with diameters as large as 3.17 mm or 0.125".
|
| |
SSMA
|
|
Sub-SMA (SSMA) are miniaturized SMA connectors that are 30% smaller than standard SMA connectors.
|
| |
SSMB
|
|
Sub-SMB (SSMB) connectors are 30% smaller than SMB connectors. They are well-suited for board-to-board applications and are designed for use with semi-rigid cables.
|
| |
SMP
|
|
Subminiature P (SMP) connectors are rated to 40 GHz and, depending on detent type, can withstand from 100 to 1,000 interconnect cycles.
|
| |
TNC
|
|
Threaded Neil-Concelman (TNC) connectors are similar in size to BNC connectors but feature a threaded coupling nut for applications that require performance to 11 GHz. TNC connectors are durable, reliable devices that are widely used in the cellular and mobile communication industry for equipment cabling and antenna interfaces.
|
| |
Triax
|
|
Triax connectors are used with triaxial cables where maximum RF shielding and minimum noise radiation is required.
|
| |
Twinax
|
|
Twinax connectors are used with twinaxial cables for balanced low level and high sensitivity circuits. Twinax connectors feature polarized key and keyway construction as well as threaded coupling.
|
| |
UHF / PL259
|
|
Ultra high frequency (UHF) connectors are economical, all-purpose connectors designed with non-constant impedance for use in comparatively low voltage and low frequency applications such as citizens' band (CB) communications systems. UHF connectors are also used in public address systems, closed circuit television (CCTV), civil defense, landing systems, ground control apparatus, ship-to-shore communications, and mobile radio equipment hookups between antenna and transmitters or receivers.
|
| |
Mini-UHF
|
|
Mini-UHF connectors are a miniature version of the original UHF connector. They feature a threaded coupling mechanism for reliable mating. Mini-UHF connectors are designed for use in cellular mobile telephone systems where size, weight and cost are critical. With crimp cable termination for low installation costs, these connectors provide excellent RF performance in applications through 2.5 GHz.
|
| |
USB Type A
|
|
Universal Serial Bus - Interconnect specification that enables instant "outside the box" plug and play peripheral connectivity. Type A connectors have a rectangular socket.
|
| |
USB Type B
|
|
Universal Serial Bus - Interconnect specification that enables instant "outside the box" plug and play peripheral connectivity. Type B connectors have a square socket.
|
| |
XLR Connector
|
|
XLR microphone type connectors, 3-pin, balanced.
|
| |
1.6 / 5.6
|
|
1.6 / 5.6 connectors are mechanically sturdy devices that feature a coupling mechanism. They are often used with equipment that requires resistance against environmental and mechanical stress. 1.6 / 5.6 connectors are also suitable for handling RF analog and digital signals in telecommunications systems.
|
| |
7-16
|
|
7-16 connectors are designed for use in medium to high power communication systems. These connectors perform exceptionally well in multichannel cellular systems where power levels approximate 100 watts per channel. Designed for both flexible as well as corrugated cables, these connectors are used in a variety of cellular base station and broadcast communication applications.
|
| |
1.0 / 2.3
|
|
1.0 / 2.3 coaxial connectors are designed for telecommunications systems that require sub-miniature 50 slide-on or screw-on connectors.
|
| |
1.85 mm
|
|
1.85 mm connectors are metric devices that derive their name from the length of the inside diameter of their outer conductor. They are used for frequencies from DC to 65 GHz.
|
| |
2.4 mm
|
|
2.4 mm connectors are metric devices that derive their name from the length of the inside diameter of their outer conductor. They are used for frequencies from DC to 65 GHz.
|
| |
2.92 mm
|
|
2.92 mm connectors are metric devices that derive their name from the inside diameter of their outer conductor. They mate with SMA and 3.5 mm connectors and provide mode-free performance to 40 GHz.
|
| |
3.5 mm
|
|
3.5 mm connectors are metric devices that derive their name from the inside diameter of their outer conductor. They are rated for frequencies up to 34 GHz.
|
| |
7 mm
|
|
7 mm connectors are metric devices that derive their name from the inside diameter of their outer conductor. Compared to other 18 GHz connectors, 7 mm devices provide the lowest reflection coefficient and the most repeatable measurements. 7 mm connectors are also know as ACP-7, an acronym for Amphenol precision connector, 7 mm.
|
| |
Other
|
|
Other unlisted, specialized, or proprietary connectors.
|
| |
Search Logic:
|
|
All products with ANY of the selected attributes will be returned as matches. Leaving all boxes unchecked will not limit the search criteria for this question; products with all attribute options will be returned as matches.
|
|
| |
Number of Contacts
|
|
The number of contacts is the number of conductive elements that mate with a corresponding element to provide an electrical path.
|
| |
Search Logic:
|
|
User may specify either, both, or neither of the "At Least" and "No More Than" values. Products returned as matches will meet all specified criteria.
|
|
