|
Search other suppliers in the following categories:
|
|
Aftercoolers are heat exchangers for cooling the discharge from a compressor.
|
|
Air compressors are machines that compress air to higher than atmospheric pressures for delivery to pneumatic or robotic tools, industrial equipment, or direct-use applications.
|
|
Air cylinders are pneumatic linear actuators that are driven by a pressure differential in the cylinder's chambers. They may be single-acting (with a spring return) or double-acting.
|
|
Air gages use pneumatic pressure and flow to measure or sort dimensional attributes.
|
|
Air hose and air duct hose is used in pneumatic systems and controls, or as supply lines for pneumatic devices and tools.
|
|
Air motors are powered by compressed air. They operate at relatively high speeds in industrial and spark-prohibited applications.
|
|
Air pressure regulators control pressure in air lines (usually adjustable) to remove fluctuations and maintain consistent pressure for pneumatic devices.
|
|
Air valves allow metered fluid flow in one or both directions. They are used in pneumatic circuits to regulate the rate of activation or exhaust of cylinders and other pneumatic devices.
|
|
Analog pressure gauges are mechanical devices that include bellows, Bourdon tubes, capsule elements and diaphragm element gauges.
|
|
Back flow preventers are assemblies consisting of two check valves and two shut off valves. These assemblies may also include test cocks for each chamber.
|
|
Booster pumps are used in applications where the normal system pressure is low and needs to be increased.
|
|
Compressed air dryers utilize technologies such as refrigeration, desiccant adsorption, and membrane filtration to remove contaminants, particularly water, from the air.
|
|
Compressed air filters are used to remove water, oil, oil vapor, dirt, and other contaminants from a compressed air supply.
|
|
Digital pressure gauges use electronic components to convert applied pressure into usable signals. The gauge readout has a digital numerical display.
|
|
Dimensional gages and instruments provide quantitative measurements of product or component dimensional and form attributes such as wall thickness, depth, height, length, inner diameter (ID), outer diameter (OD), taper or bore.
|
|
Filter, regulator, lubricator (FRL) assemblies are pre-packaged or modular assemblies of common configurations of air filters, regulators, lubricators, and gauges.
|
|
Filtration media and elements are designed to remove suspended particles from a process stream. This product area includes bulk filter media, cartridges, housing-only products, and housing and filter assemblies.
|
|
Flow controllers monitor and maintain flow-rate variables, typically in process applications.
|
|
Flow meters (flowmeters) and flow sensors are devices used for measuring the flow rate or quantity of a moving fluid or gas.
|
|
Flow orifices and flow restrictors contain precision-machined holes and filters or screens to restrict flow and reduce pressure. They are available as stand-alone devices and in kits, assemblies, restrictors, and restrictor valves.
|
|
Hose fittings are a category of components used to connect hoses and tubes for in-line, offset, multi-port, and mounting configurations.
|
|
Hose reels are used to wind, unwind, and store lengths of hose that are designed to transport gases and liquids for industrial applications.
|
|
Hydraulic accumulators use an incompressible fluid and a compressed gas, spring or raised mass to store energy, absorb shock, eliminate noise, and counter-balance loads.
|
|
Hydraulic cylinders are actuation devices that utilize pressurized hydraulic fluid to produce linear motion and force.
|
|
Hydraulic filters are used for handling petroleum-based oils, emulsions, synthetic hydraulic fluids and lubrication oils.
|
|
Hydraulic hose is used in wide variety of industrial hydraulic systems.
|
|
Hydraulic oils and transmission fluids are used to transmit power in hydraulic equipment and power transmission applications.
|
|
Hydraulic power units provide pressurized flow to hydraulic motors, cylinders, and other components.
|
|
Hydraulic pumps deliver high-pressure fluid flow to the pump outlet. Hydraulic pumps are powered by mechanical energy sources to pressurize fluid.
|
|
Hydraulic regulators maintain the output pressure at a set value.
|
|
Hydraulic reservoirs are storage tanks that hold liquids or gases used in fluid power applications. They are usually rectangular, cylindrical, T-shaped, or L-shaped and made of steel, stainless steel, aluminum, or plastic.
|
|
Hydraulic valves contain and transfer the flow and pressure of hydraulic fluid in hydraulic power systems. They range from simple shutoff valves to precision control valves.
|
|
Industrial air filters reduce the number of particles in the air that passes through them.
|
|
Industrial hose covers the broad spectrum of fluid transfer lines. Hose is usually flexible, often reinforced, and available in a wide range of material compositions to cover various hydraulic and pneumatic industrial applications.
|
|
Industrial liquid handling pumps are classified in many different ways, and are distinguished by the media pumped and the fluid motive mechanism (dynamic or displacement).
|
|
Industrial valves are classified in many different ways. They can be distinguished by material of construction, media handled, and/or application.
|
|
Lubricators and lubrication systems are used to apply controlled or metered amounts of lubricant.
|
|
Pneumatic lubricators in compressed air lines atomize oil into aerosol form for injection into the air stream to lubricate downstream pneumatic tools, cylinders, motors, and valves.
|
|
Power tools include a wide range of devices for fabrication, assembly, construction, and repair. They are usually motor-driven.
|
|
Pressure gauges are used for a variety of industrial and application-specific pressure monitoring applications. Uses include visual monitoring of air and gas pressure for compressors, vacuum equipment, process lines and specialty tank applications such as medical gas cylinders and fire extinguishers.
|
|
Pressure regulators are used to maintain a constant outlet pressure or flow.
|
|
Pressure switches are actuated by a change in the pressure of a liquid or gas. They activate electromechanical or solid-state switches upon reaching a specific pressure level.
|
|
Reels are devices around which lengthy, continuous items such as cable, wires, paper, etc. are wrapped for transportation or storage.
|
|
Rodless cylinders are linear devices that use pressurized fluid to move a load within many power transfer operations.
|
|
Tube fittings connect runs of tubing for in-line, offset, multi-port, and mounting configurations to other tubing sections, pipe, hose, and other fluid transfer components.
|
|
Tubing is used to transport fluid and gas in pneumatic, hydraulic, or process applications. Tubing differs from pipe in that tubing's outside diameter or size is controlled and used for product designation.
|
|
Valve positioners compare a control signal to a valve actuator’s position and move the actuator accordingly. They are used with both linear valves and rotary valves.
|
