|
Search other suppliers in the following categories:
|
|
Abrasives and abrasive products are used to remove surface materials such as metal, ceramics, glass, plastics, and paint. Abrasives and abrasive products include discs, belts, blast machines and sandblasters, as well as sheets, rolls, and hand pads.
|
|
Ball valves provide tight shut-off and characterizable control. They have high rangeability due to the design of the regulating element, without the complications of side loads typical of butterfly or globe valves.
|
|
Battery packs are constructed from two or more individual cells or batteries.
|
|
Butterfly valves control flow through a circular disc or vane by turning the valve's pivot axis at right angles to the direction of flow in the pipe. They are normally used as throttling valves to control flow.
|
|
Check valves are self-activating safety valves that permit gases and liquids to flow in only one direction, preventing process flow from reversing. They are classified as one-way directional valves.
|
|
Dial thermometers are bimetal or bi-metallic, liquid or gas-filled, and vapor-tension-based. These devices display temperatures in Fahrenheit, Celsius, or both.
|
|
Diaphragm seals are isolation devices that separate a pressure instrument from the process media.
|
|
Diaphragm valves close by means of a flexible diaphragm attached to a compressor.
|
|
Digital thermometers are portable temperature sensing devices that have permanent probes and a digital display.
|
|
Expansion joints connect two fixed assemblies or pipes and provide allowance for movement due to service load, shock, or thermal cycles.
|
|
Gaskets are used to prevent fluid or gas leaks by providing a barrier between two mating surfaces.
|
|
Gate valves and knife valves are linear motion valves in which a flat closure element slides into the media stream to shut off flow.
|
|
Globe valves are linear motion valves with rounded bodies, from which their name is derived. They are widely used in industry to regulate fluid flow in both on/off and throttling service.
|
|
Hose fittings are a category of components used to connect hoses and tubes for in-line, offset, multi-port, and mounting configurations.
|
|
Industrial adhesives consist of hot melt adhesives, epoxy adhesives, polyurethane adhesives, sealants, thermoset adhesives, UV curing adhesives, silicon adhesives, acrylic adhesives and other related industrial products.
|
|
Industrial batteries translate chemical energy into electricity.
|
|
Industrial hoists are lifting and pulling devices that use a cable, rope, or chain to move or lift a load. Hoists are primarily used for vertical lifting, and usually have a feature for ceiling mounting such as a hook or trolley mount.
|
|
Industrial hose covers the broad spectrum of fluid transfer lines. Hose is usually flexible, often reinforced, and available in a wide range of material compositions to cover various hydraulic and pneumatic industrial applications.
|
|
Industrial lubricants are oils, fluids, greases and other compounds designed to reduce friction, binding or wear and exclude moisture. Specialized characteristics may enhance thermal conduction across thermal interfaces or reduce electrical resistivity across electrical joints.
|
|
Industrial pipe is a broad category of fluid and solid transport hardware used in many applications and industries. Cylindrical pipe and rigid tube is used in process, energy, construction, and civil infrastructure applications.
|
|
Laboratory air handling equipment is used to protect specimens and laboratory staff from environmental contamination. Products include fume hoods, biological safety cabinets, environmentally controlled rooms and clean benches.
|
|
Lifting jacks are used for leveling or positioning heavy equipment, or for supporting structures. They use screw or cylinder-based actuators and are powered by hydraulic, mechanical, electric, or manual methods.
|
|
Limit switches are electromechanical or solid state devices that require the physical contact of an object with the switch’s actuator to make the contacts change state.
|
|
Manifolds and manifold systems are fluid-distribution devices. They range from simple supply chambers with several outlets to multi-chambered flow control units including integral valves and interfaces to electronic networks.
|
|
Needle valves are small valves used for flow control in liquid or gas services. The fine threading of the stem and the large seat area allow for precise resistance to flow.
|
|
Pipe fittings cover many components that connect pipe ends for in-line, offset, multi-port, and mounting configurations.
|
|
Quarter-turn plug valves use a cylindrical or tapered plug with a hole in the center to control straight through flow when in the open position.
|
|
Pressure gauges are used for a variety of industrial and application-specific pressure monitoring applications. Uses include visual monitoring of air and gas pressure for compressors, vacuum equipment, process lines and specialty tank applications such as medical gas cylinders and fire extinguishers.
|
|
Pressure relief valves are self-actuated safety valves designed to relieve excess pressure upstream from the line.
|
|
Pressure switches are actuated by a change in the pressure of a liquid or gas. They activate electromechanical or solid-state switches upon reaching a specific pressure level.
|
|
Quick couplers are used in a hydraulic or pneumatic system to quickly connect lines without losing fluid or fluid pressure.
|
|
Solenoid valves are devices that use a solenoid to control valve activation.
|
|
Specialty or proprietary products and accessories related to laboratory safety equipment.
|
|
Temperature instruments use contact or noncontact methods to measure temperature. Products include dial, digital, industrial and laboratory thermometers; temperature probes, indicators, and sensors; RTD elements and transmitters; and thermistors, thermocouples, thermopiles, and thermal switches.
|
|
Thermowells are designed to accept numerous types of temperature probes. They are used to easily facilitate the repair of temperature sensing devices without interrupting the process being monitored.
|
|
Tube fittings connect runs of tubing for in-line, offset, multi-port, and mounting configurations to other tubing sections, pipe, hose, and other fluid transfer components.
|
|
Vacuum gauges are devices for measuring vacuum or sub-atmospheric pressures.
|
|
Valve actuators mount on valves and, in response to a signal, move a valve to a desired position using an outside power source.
|
|
Vises are used for work holding and during inspection, assembly, forming, welding, and machining operations. They usually consist of a screw, level, or cam-type mechanism that closes and holds two or more jaws around a workpiece
|
