|
Click on a category to narrow your results.
|
|
|
Home
|
| |
|
|
|
Product Categories for flow measurement
Flow Meters -
(1064 company listings)
Flow meters (flowmeters) and flow sensors are devices used for measuring the flow rate or quantity of a moving fluid or gas
Search by Specification |
Find more about Flow Meters
|
Gas Flow Meters -
(276 company listings)
Gas flow meters are used for measuring the flow or quantity of a moving gas in an enclosed pipe or passage
Search by Specification |
Find more about Gas Flow Meters
|
Liquid Flow Meters -
(401 company listings)
Liquid flow meters are used for measuring the flow or quantity of a moving fluid
Search by Specification |
Find more about Liquid Flow Meters
|
Mass Flow Switches -
(33 company listings)
Mass liquid flow switches and mass gas flow switches are devices used for measuring the flow or quantity of a moving liquid or gas in terms of a unit of mass per unit time, such as pounds per minute.
Search by Specification |
Find more about Mass Flow Switches
|
Velocity Flow Switches -
(70 company listings)
Gas flow switches and liquid flow switches, velocity, are used to measure the flow or quantity of a moving fluid in terms of velocity, such as feet per minute
Search by Specification |
Find more about Velocity Flow Switches
|
Liquid Flow Switches, Volumetric -
(114 company listings)
Volumetric liquid flow switches are devices with a switch output used for measuring the flow or quantity of a moving fluid in terms of a unit of volume per unit time, such as liters per minute.
Search by Specification |
Find more about Liquid Flow Switches, Volumetric
|
Gas Flow Switches, Volumetric -
(60 company listings)
Volumetric gas flow switches are devices with a switch output used for measuring the flow or quantity of a moving gas in terms of a unit of volume per unit time, such as cubic feet per minute
Search by Specification |
Find more about Gas Flow Switches, Volumetric
|
|
|
Machine Design Search Results for flow measurement
Machine Design -
... Flow nozzles are expensive and may cause permanent pressure loss. Pitot tubes provide basic flow measurement for laboratory tasks. A pitot tube consists of a special tube facing into the flow to ...
|
Basics of Design Engineering - Fluid Power Chapter 2 - Filters, Heat Exchangers...
... Flow nozzles are expensive and may cause permanent pressure loss. Pitot tubes provide basic flow measurement for laboratory tasks. A pitot tube consists of a special tube facing into the flow to ...
|
Fluid Power Monthly - April, 2007
Hedland Flow Meters. Effectively engineered flow measurement solutions for oil, phosphate ester, water, water-based fluids, air and compressed gases.. Learn more at hedland.com.. DIGI-KEY CORPORATION ...
|
Fluid Power Monthly - May, 2007
Hedland Flow Meters. Effectively engineered flow measurement solutions for oil, phosphate ester, water, water-based fluids, air and compressed gases.. Learn more at hedland.com.. Kurt Hydraulics. Kurt ...
|
Basics of Design Engineering - Fluid Power Chapter 2 - Filters, Heat Exchangers...
Measurement accuracy depends largely on the number of levels chosen to define the tank and system calibration. The MPU then drives a display, either digital or analog, to show the level of liquid in ...
|
Machine Design -
Precise measurement of the screw rotation corresponds to a linear piston position. The controller processes this information and signals the servovalve to maintain or change flow accordingly. Hall-effect ...
|
Machine Design -
Transducer output flow is about 0.1 scfm at 15 psig, a rate that is too slow to actuate many components in a reasonable time. To overcome this problem, flow rate can be increased with the use of a ...
|
Basics of Design Engineering - Electrical/Electronic - I/O Devices - Other ...
Transducer output flow is about 0.1 scfm at 15 psig, a rate that is too slow to actuate many components in a reasonable time. To overcome this problem, flow rate can be increased with the use of a ...
|
Machine Design -
Measurement accuracy depends largely on the number of levels chosen to define the tank and system calibration. The MPU then drives a display, either digital or analog, to show the level of liquid in ...
|
Basics of Design Engineering - Engineering Materials - Plastic Design Basics - ...
But stock forms of plastics are made by extrusion, not injection molding. Besides not having the same flow orientation of a molded part, extrusions of a given material are usually made from a higher ...
|
|
|
|
