|
Click on a category to narrow your results.
|
|
|
Home
|
| |
|
|
|
Product Categories for rated output
Data Acquisition Output Modules -
(154 company listings)
Data acquisition output modules or cards transfer amplified, conditioned, or digitized signals
Analog Input Channels:
|
|
|
Digital I/O Channels:
|
|
|
Search by Specification |
Find more about Data Acquisition Output Modules
|
Impedance Matching Networks -
(18 company listings)
Impedance matching networks are electrical circuits which, when connected between two networks, match the output impedance of the source (the first network) to the input impedance of the load (the receiving or second network).
Search by Specification |
Find more about Impedance Matching Networks
|
AC Power Sources -
(222 company listings)
AC power sources provide alternating power and typically have adjustable output values for the testing of component response at various voltage, current and frequency levels
Search by Specification |
Find more about AC Power Sources
|
Power Transformers -
(840 company listings)
Power transformers convert power-level voltages from one level or phase configuration to another.
Search by Specification |
Find more about Power Transformers
|
Level Sensors, All Types -
(744 company listings)
Level sensors are used to detect liquid or powder levels, or interfaces between liquids.
Search by Specification |
Find more about Level Sensors, All Types
|
Gearboxes and Gearheads -
(615 company listings)
Gearboxes and gearheads are speed reducers that consist of a set of gears, shafts, and bearings in an enclosed housing.
Search by Specification |
Find more about Gearboxes and Gearheads
|
Audio Transformers -
(89 company listings)
Audio transformers are involved in the transmission of voice or sound signals.
Search by Specification |
Find more about Audio Transformers
|
|
|
Machine Design Search Results for rated output
Machine Design -
LEDs are generally rated for operation at room temperature. Operating at higher temperatures can cause light intensity to drop to as low as 75% of the rated output. Continuous operation at high ...
|
Basics of Design Engineering - Electrical/Electronic - Displays and Display ...
LEDs are generally rated for operation at room temperature. Operating at higher temperatures can cause light intensity to drop to as low as 75% of the rated output. Continuous operation at high ...
|
Machine Design -
For regulated power supplies, output voltage more precisely matches the rated value but does vary slightly with changes in line voltages and load current. Furthermore, output voltage is influenced by ...
|
Basics of Design Engineering - Fluid Power Chapter 6 - Power Actuators, Motors ...
Hydrokinetic drives are typically rated from 1 to 5,000 hp but higher ratings are common. Largest units are rated at 25,000 to 30,000 hp. Because there is no mechanical lockup between the driver and ...
|
Machine Design -
Flow: A flow curve is obtained by cycling the valve over the rated input current range and recording a continuous plot of output flow versus input current for one cycle. It is used to measure valve ...
|
Basics of Design Engineering - Fluid Power Chapter 7 - Power Modulation and ...
Flow: A flow curve is obtained by cycling the valve over the rated input current range and recording a continuous plot of output flow versus input current for one cycle. It is used to measure valve ...
|
Machine Design -
The functional difference between precision and general-purpose regulators is the degree of control accuracy of the output pressure. Output pressure accuracy is determined by the droop due to flow ...
|
Machine Design -
Torque increases as current approaches the rated value. At or near rated current in conventional stepping motors, a larger part of the air-gap flux traverses the gap from stator slot to rotor slot ...
|
Basics of Design Engineering - Electrical/Electronic - I/O Devices - ...
They also have low output impedance. This means that connecting them with oscilloscopes or chart recorders is relatively easy. The primary disadvantage of internally amplified units it that they ...
|
Basics of Design Engineering - Fluid Power Chapter 7 - Power Modulation and ...
The functional difference between precision and general-purpose regulators is the degree of control accuracy of the output pressure. Output pressure accuracy is determined by the droop due to flow ...
|
|
|
|
